Ipc 6013b

All via structures shall be represented in the thermally stressed evaluations. Immersion silver plating is available in two very distinct but acceptable versions - a thin silver deposit and a thicker silver deposit Other Metals and Coatings Other depositions, such as palladium, rhodium, tin, solder alloys, etc. The measurement of the annular ring on external layers is from the inside surface within the hole of the plated hole, or unsupported hole, to the outer edge of the annular ring on the surface of the PB as shown in Figure Flexible PBs shall be free of defects in excess of those allowed in this specification. The presence of nail heading may be considered an indicator of process or design variation but is not a cause for rejection.

Uploader: Mazuktilar
Date Added: 14 October 2007
File Size: 59.98 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 24636
Price: Free* [*Free Regsitration Required]





The field More information.

IPCC: thecritic.info: Books

All fees quoted in U. All dimensional characteristics such as, but not limited to, PB periphery, thickness, cutouts, slots, notches, holes, scoring and edge board contacts to connector key area shall be as specified in the procurement documentation.

Testing in accordance with IPC-TM, Method Shall meet requirements of Table or as specified in procurement documentation, isolated areas of reduced copper thickness shall be measured and evaluated to the copper plating void rejection criteria specified in Copper: Supply Chain This copy is uncontrolled unless otherwise. A chip of coverlay or covercoat adhered to exposed adhesive that does not fall off when rubbed with isopropyl impregnated applicator shall be acceptable for Class 1 and Class 2 product.

How can we make them go away? As both increase, the amount of time to properly wet the sides of the holes and the tops of the lands increases proportionately.

The marking shall be produced by the same process as used in producing the conductive pattern or by use of a permanent fungistatic ink or paint seeLASER marker, or a vibrating pencil marking on a permanently attached label or metallic area provided for marking purposes. When the procurement documentation specifies a minimum copper thickness for conductors, the conductor shall meet or exceed that minimum thickness.

Use C High temperature environment over C [ F].

Figure d c Bending Test IPCb The specified number of bend cycles shall be performed with the mandrel placed in contact with the specimen on one side and then again with the mandrel placed in contact with the specimen on the opposite side. Supplier in-process certification of features of accuracy to reduce inspection is allowed provided the method icp documented and demonstrates capability to meet the specified requirements.

Unless prohibited by the customer, the employment of filleting or tear drops to create additional land area at the conductor junction shall be acceptable for Class 1 and Class 2 and in accordance with general requirements for lands with holes detailed in IPC Employment of filleting or tear drops in Class 3 product shall be AABUS.

Adopted October 6, Why is there a charge for this document?

Vulcanize pad to sole plate - adhesives epoxies are unacceptable; Handwritten: Circuit repairs shall not violate the minimum electrical spacing requirements Rework Rework is permitted for all classes.

If a particular product is determined to be critical by the kpc and a smaller index value is required, the user shall designate the requirement in the procurement document and should state the critical requirement on the master drawing.

IPC Testing

Will is used to express a declaration of purpose. The physical geometry of a conductor is defined by its width 6013 thickness x length. Minimum edge to conductor spacing shall be specified in the procurement documentation Transition Zone, Rigid Area to Flexible Area The transition zone is the area centered on the edge of the rigid portion from which the flex portion extends. The inspection range is limited to 3.

Each void shall not exceed 2. Ipd Copper Gap Max. Marking inks shall be applied to either the flexible PB or to a label applied to the flexible PB.

IPC-6013B Qualification and Performance Specification for Flexible Printed Boards

Thicker or more complex specimens may require longer baking times. When automated test equipment is used, the minimum applied test voltage shall be the maximum rated voltage of the PB. MIL-I is broken down into four categories: Microsection analysis is performed per Unless prohibited by the customer, the employment of filleting or tear drops to create additional land area at the conductor junction shall be acceptable for Class 1 and Class 2 and in accordance with general requirements for lands with holes detailed in Ioc Employment of filleting or tear drops in Class 3 product shall be AABUS.

Covercoats may have reduced performance in tight bend radius applications. The allowable reductions assume that the manufacturer at front end tooling CAM understands their lpc allowance and adds a producibility compensation to the original artwork design Conductor 6013h Reduction Allowable reduction of the minimum conductor thickness due to isolated defects i.

IPC Testing and Certification | NTS

Cracks between two uncommon conductors in either the horizontal or vertical direction shall not decrease the minimum dielectric spacing Delamination or Blistering For Class 2 and Class 3 there shall be no evidence of delamination or blistering.

Information that should be included in the procurement documentation is shown in IPC-D Over exhibitors and over 5, attendees typically participate each year. Other dielectric materials may be ippc on the procurement documentation Metal Foils Copper foil should be in accordance with IPC Foil type, foil grade, foil thickness, bond enhancement treatment, and foil profile should be specified on the master drawing if critical to the function of the flexible PB.

Tygocage

1 Comments

Dousar Posted on10:12 pm - Oct 2, 2012

It is remarkable, very good piece